martintools.net

Home > Fax Error > Canon Fax Error Code Ng

Canon Fax Error Code Ng

Contents

Cause: Cannot receive signals properly due to poor line conditions. Chapter 1 User Error Codes Chapter! : User Error Codes #001 [ TX ] Document has jammed Cause Remedy • The document is trapped in the feeder. • The document is A. Cause Remedy... have a peek at this web-site

Remedy Allow Fax Driver TX in Send in Function Settings (Settings/Registration) is set to 'Off'. Solution: Adjust the NL equalizer to receive EOM from the other party properly. ##606 [ RX I Fail phase synchronization during MF1 reception. Cause: The BJ controller in the BJ printer control unit is faulty. Remedy Wait until the Address Book Import/Export function from the Remote UI or the other sending component is complete, and then try sending again. #711 Cause 1 The Mail Box and http://www.worldoffax.com/G3%20Service%20Codes.htm

Canon Fax Error Code Ng

Remedy Check the system's available memory, and delete unnecessary documents in the Mail Box and Fax/I-Fax Inbox. (See "Scan and Store," "Fax/I-Fax Inbox," and "Access Stored Files.") Cause 2 The memory Cause: Abnormal protocol. Solution: Have the other party lower their transmission start speed to 4800 bps Solution: Adjust the NL equalizer so that the picture signal can properly be received. ##106 [ B.

Solution: Add a long pause after the telephone number when registering the user in the auto- dialing directory so that the system will not respond to the first DIS from the Cause: The other party cannot receive ACK properly due to poor line conditions. Page 216 Chapter 2: Service Error Codes ##1063 [ TX/RX ] Service or option not available, unspecified Cause Remedy • Cause number #63 (Service or option not • Check the terms Canon Fax Error Code 104 Cause: Malfunction due to CFR echo.

Page 166 Chapter 2: Service Error Codes ##740 [ RX ] In CHT reception, the other party could not use fall-back Cause Remedy • The line condition is poor, and TCF Canon Fax Machine Error Codes Wait a while, and available) arrived from network. These errors can occur if the phone lines in the area to be faxed are old or there is noise (static on the phone line). https://support.usa.canon.com/kb/index?page=content&id=ART141048 Printing the Fax TX Report 1.

Remedy Check the destination setting. #803 Cause 1 The connection was interrupted due to reasons on the recipient's side before all of the pages could be sent. Canon Result Ng Cause: Abnormal protocol. Solution: Power cycle the machine (unplug unit). Solution: Boost the transmission level so the other party can receive the picture signals properly.

Canon Fax Machine Error Codes

Page 79 MCF, RTP, RTN, PIP, or PIN was received Cause Remedy • The procedure signal is faulty. • Record the protocol on a DAT or MD, and have it analyzed original site Remedy First, check the telephone line number for the server machine. (See [Set Line] in "Settings/Registration Table.") Then, set the correct telephone line number for the server machine in Remote Fax Canon Fax Error Code Ng Page 133 Chapter 2: Service Error Codes ##343 [ TX/RX ] Ink absorber for ink detection has become full Cause Remedy • The ink absorber for ink detection has be- • Canon Error #099 Call the telephone provider if line conditions fail to improve.

Note: if the capacity of the absorption pad is unclear, register a value corresponding to the quantity of absorbed ink in pad Solution: Replace the PCNT PWB, and register a Check This Out A. For this reason, there may be information in this manual that does not apply to your locality. Solution: Replace the OPT2 control unit (OPT2 unit, etc.). ##260 [ TX / RX ] System error between modem and SCNT. Canon Fax Error #099

Remedy Confirm that the recipient's machine is able to communicate, and then try again. Page 217 Chapter 2: Service Error Codes ##1066 [ TX/RX ] Channel type not implemented Cause Remedy • Cause number #66 (Channel type not • Check the terms of the contract A. Source If a sequential broadcast transmission is performed when Fax TX Report is set to 'On', a Fax Multi TX Report is printed. (See "FAX MULTI TX REPORT.") » Basic Operations »

Cause: Carriage motor does not work. G3 Fax Page 170 Cause Remedy • The procedure signal is faulty. • Record the protocol on a DAT or MD, and have it analyzed by the local Canon office and/or Technical Center. Page 80 Chapter 2: Service Error Codes ##115 [ TX ] During image transmission, the maximum transmission time per line was exceeded Cause Remedy • The document is too fine, and

Configure the machine to start reception at a lower speed.

Page 66 [ RX ] In G2 reception, a signal other than PIS or GC2 is received after transmission of MCF2 or GI2 Cause Remedy • The procedure signal has a Cause 3 The settings on your machine do not match the settings on the recipient's machine. Cause: The ink detection waste ink tank is full. Reserved Communication Jobs Were Cleared. Page 169 Chapter 2: Service Error Codes ##754 [ TX ] In ECM transmission, the allowed number of procedure signal re-transmissions was exceeded after transmission of PPS-NULL Cause Remedy • The

Configure the local fax machine to use a slower reception speed. Solution: Replace the SCNT PWB. ##348 [ TX / RX ] Ink detection sensor error. Cause: Continuous line noise Solution: Have the other party boost their transmission level so signals can be received B. have a peek here Support Forum Join the conversation!

© Copyright 2017 martintools.net. All rights reserved.