martintools.net

Home > File Transfer > File Transfer Error During Download. Protocol Error Code Is 3

File Transfer Error During Download. Protocol Error Code Is 3

Also consider curl_multi_strerror. CURLE_URL_MALFORMAT (3) The URL was not properly formatted. Protocol Error Code Is 3 error is the Hexadecimal format of the error caused. On a scale of 1-5, please rate the helpfulness of this article 1 2 3 4 5 Not Helpful Very Helpful Optionally provide private feedback to help us improve this article... have a peek here

done. There are two (2) ways to fix File Transfer Error During . This return code only appears if --fail is used. 23 Write error. File unavailable (e.g., file busy). https://supportforums.cisco.com/discussion/10685011/cue-upgrade

Various reading problems. 27 Out of memory. Thank you for your feedback! Please wait .................. CURLE_SSH (79) An unspecified error occurred during the SSH session.

A specified outgoing interface could not be used. 46 Bad password entered. The requested page was not found. A required LDAP function was not found. 42 Aborted by callback. Your cache administrator is webmaster.

Starting Kernel. y- After that, configure your CUE! The corrupted system files entries can be a real threat to the well being of your computer. In this case the server is required to provide meaningful description of the error itself (see above).

Re: Payload file is missing while upgrading CUE Souley Sep 30, 2012 6:50 AM (in response to Michael CCIE 38404) Mike if i remember i added the language file to my Only a part of the file was trans- fered. 19 FTP couldn't download/access the given file, the RETR (or similar) command failed. 20 FTP write error. One possible reason is that the advisory read-only attribute-bit is set. 23 Invalid parameter One of the parameters was out of range, or the parameters specified cannot be used together. 24 Login ISM0/0 first and finish initilizing by setup admin / pwd 9.

validblock_diagnose, code = 17 current memory block, bp = 0xC1EA5D2C, memorypool type is Processor data check, ptr = 0xC1EA5D5C next memory block, bp = 0xC1EA5D7C, memorypool type is Processor data check, The server does not support this command. 503 Bad sequence of commands. Continue... Open C User Access Verification Username: admin Password: CUE_Router# 5.

FTP uses two ports: 21 for sending commands, and 20 for sending data. http://martintools.net/file-transfer/file-transfer-manager-error-code-12057.html Try switching from PASV to PORT mode, or try increasing the time-out value. 10061 Cannot connect to remote server. Some servers use this code instead of 421 when the user limit is reached 532 Need account for storing files. Add additional language pack on FTP folder (ex, /cue-vm-k9.SPA.sme.8.6.9) US language pack : cue-vm-en_US-langpack.sme.8.6.9.prt1 4.

Proceed as usual. Article has been viewed 601K times. Also are you using the loopback address or vlan addressing for you service module ip address and default gateway. http://martintools.net/file-transfer/file-transfer-manager-error-code-2.html An application told curl to abort the operation. 43 Internal error.

Note: The manual fix of File Transfer Error During . Initializing memory. Download latest CUE and language pack from Cisco website. * Download from /Cisco Interfaces and Modules/Services-Ready Engine (SRE) Modules/Unity Express for SRE /Unity Express Complete Installation File Set-8.6.9 2.

Loading disk:/bzImage ...

I would do my install and everything would go fine. Error code list for failed FTP and HTTP remote webserver log transfers Overview An Urchin Log Source can be configured to collect a webserver log from a remote server via FTP Extract a file on FTP server (local or remote) 3. INIT: Switching to runlevel: 4 INIT: Sending processes the TERM signal ==> Starting CDP STARTED: ntp_startup.sh STARTED: LDAP_startup.sh STARTED: SQL_startup.sh STARTED: dwnldr_startup.sh STARTED: HTTP_startup.sh STARTED: probe STARTED: fndn_udins_wrapper STARTED: superthread_startup.sh STARTED:

Memory initialization OK. CURLE_QUOTE_ERROR (21) When sending custom "QUOTE" commands to the remote server, one of the commands returned an error code that was 400 or higher (for FTP) or otherwise indicated unsuccessful completion Rebooting ... this contact form CURLM_OK (0) Things are fine.

This article contains information that shows you how to fix File Transfer Error During . Return code is success. It will cause re-configure basic setup and reload SRE system. (INIT)se-192-168-77-254# SYSTEM ONLINE se-192-168-77-254# 11. There can be many events which may have resulted in the system files errors.

CURLE_NOT_BUILT_IN (4) A requested feature, protocol or option was not found built-in in this libcurl due to a build-time decision. The given remote host was not resolved. 7 Failed to connect to host. 8 FTP weird server reply. A quote command returned error from the server. 22 HTTP not found. See More 1 2 3 4 5 Overall Rating: 0 (0 ratings) Log in or register to post comments ActionsThis Discussion 0 Votes Follow Shortcut Abuse PDF     Trending Topics

i tried some technics like using the current license file in the CUE that didn't work. Proceed as usual. curl_easy_strerror can be called to get an error string from a given CURLcode number. CURLE_FTP_WEIRD_PASV_REPLY (13) libcurl failed to get a sensible result back from the server as a response to either a PASV or a EPSV command.

At this point if it won't even boot have you tried reseating the card?--ms Like Show 0 Likes (0) Actions Join this discussion now: Log in / Register 5. Logged in user does not have permission to store files on remote server. 550 Requested action not taken.

© Copyright 2017 martintools.net. All rights reserved.